Mugen

This is a set of optional Mugen 0.95mm Clutch Springs. The stiffer the spring, the later the clutch will engage allowing the engine to spool up to ...

This is a pack of 8 3x16.8mm wheel hub pins for the Mugen MBX5 family of buggies. These are the small pins that are used to secure the wheel hubs t...

This is an optional Mugen 70mm Front Shock Spring Set, and is intended for use with the Mugen MBX7 1/8 scale nitro buggy. These 1.6 springs provide...

This is an optional Mugen 70mm Front Shock Spring Set, and is intended for use with the Mugen MBX7 1/8 scale nitro buggy. These 1.6 springs provide...

This is a replacement Mugen Fuel Tank. The internal fuel baffles on this tank have been installed to increase fuel pick up and keep the fuel clunk ...

This is a pack of ten replacement Mugen HTD S6 Silicon O-Rings for use with the HTD (High Traction Diff) Differentials. 

This is a replacement Mugen 46 Tooth MBX8 ECO HTD Plastic Spur Gear.

This is a replacement Mugen MBX8 Front Bumper.

This is a replacement Mugen MBX8 Front Lower Suspension Arm Set. This set also includes the plastic arm inserts, but no mounting hardware. Optional...

This is a pack of four replacement Mugen Front Shock Boots, and are intended for use with the Mugen MBX7 1/8 scale nitro buggy. Because these updat...

This is a replacement Mugen Front Upper Suspension Arm Set. These front upper suspension arms have been shortened 1.6mm in length. This will allow ...

This is a set of two Mugen front or rear driveshaft bones, and are intended for use with the Mugen MBX8 1/8 scale buggy.

This is a replacement Mugen Rear Hub Carrier Set. These rear hub carriers has been modified to allow for use of an 8mm x 16mm ball bearing which is...

This is a pack of four replacement Mugen Rear Shock Boots, and are intended for use with the Mugen MBX7 1/8 scale nitro buggy. Because these update...

This is a Mugen 2.2mm Front anti-roll bar, and is intended for use with the Mugen MBX8 and MBX8T 1/8 scale vehicles. Effects of Front Roll Bar Adj...

This is a Mugen 2.3mm Front anti-roll bar, and is intended for use with the Mugen MBX8 and MBX8T 1/8 scale vehicles. Effects of Front Roll Bar Adj...

This is a Mugen 2.5mm Rear anti-roll bar, and is intended for use with the Mugen MBX8 and MBX8T 1/8 scale vehicles. Effects of Front Roll Bar Adju...

This is a Mugen 2.8mm rear anti-roll bar, and is intended for use with the Mugen MBX8 and MBX8T 1/8 scale vehicles. Effects of Rear Roll Bar Adjus...

This is a replacement Mugen MBX8/8T Aluminum "B" Front/Rear Position Wing Washer

This is a set of three Mugen "Hard" Aluminum Clutch Shoes and are intended for use with the Mugen family of 1/8 scale vehicles or any other vehicle...

This is a replacement Mugen Complete Bushing Set, and is intended for use with the Mugen MBX8 1/8 scale nitro buggy. This complete set includes all...

This is a set of four replacement Mugen Damper Cap Bushings, and are intended for use with the Mugen MBX8 family of 1/8 Scale vehicles.

This is a replacement Mugen Damper End Set, and is intended for use with the Mugen MBX8 family of 1/8 Scale vehicles. This set includes four shaft ...